Skip to the beginning of the images gallery

(CS-D507E) Closed Loop Stepper Drive

£77.42 £64.52

Icon	Label	Description	Type	Size	Download
	CS-D507E_User_Manual	user manual for the CS-D507E	pdf	1.2 MB	Download
	Leadshine-Motion-Studio-Stepper-V1.3.10	A free software which allows the user to modify the parameters of Leadshine's stepper and servo drives, performance adjustments, trial run, monitor the status etc.	zip	29 MB	Download

Categories: CS Closed Loop Drive (Step and Dir),

SKU

CS-D507E

-3 in stock. (If not in stock expect 4-5 weeks)

More Information on Shipping

(CS-D507E) Closed Loop Stepper Drive

More Information
Country of Manufacture	China
Manufacturer	Leadshine

Details

Leadshine CS-D507E is a closed loop stepper drive. When used to drive a 2-phase stepper motor in frame sizes NEMA 8, 17, 23, or 24 with incremental rotary encoder, it can close the position loop between the motor and drive and therefore eliminate the loss of step problem in an open loop system. The CS-D507E adopts Leadshine advanced control algorithm. It is very easy to configure and setup. It It is ideal for upgrading open loop stepper systems or replacing servo systems in some low to middle speed applications.

Compared with an open loop stepper system, a CS-D507E adopted closed loop stepper system can eliminate loss of step, make real-time position error correction, and use 100% available torque of the driven stepper motor. It can also power the driven stepper motor with reduced heating, lower noise, low vibration, …

When compared with a servo system, a CS-D507E adopted closed loop stepper system can have much higher low-to-middle-speed torque. such a control system also has the advantages of no tuning, no hunting, no overshooting, and much lower cost.

Step & direction or CW/CCW control modes
Supply voltage of 20-50 VDC, maximum output current of 8.0A
Powering 2-phase stepper motors of NEMA 8, 11, 14, 17, 23, and 24
Fault output, brake control, or in-position output.
No lose of steps for closed position loop.
Auto-tuning to match wide-range NEMA 17, 23 and 24 closed-loop stepper motors.
Enhance performance, especially at low-speed application (<60RPM).
Max 500 KHz input frequency.
15 micro step settings of 800-51,200 via DIP switches, or 200-51,200 via software.
2 out current settings and gain tuning via S1 rotating switch.
Reduced motor heating and more efficient
Smooth motion and super-low motor noise
CE certified and RoHS compliant.

Model:	CS-D507E
Phase:	2
Control Mode:	Step & Direction, CW & CCW
Max Input Frequency:	200 KHz
Input Voltage Range:	20 - 50 VDC
Suggested Power Supply Voltage Range:	24 - 48 VDC
Software Cofig. Microstep Range:	200 - 512,000 (increased by 200)
# of DIP Switch Microstep Configurations:	16
DIP Switch Microstep Settings:	800, 1600, 3200, 6400, 12800, 25600, 51200, 1000, 2000, 4000, 5000, 8000, 10000, 20000, 40000
Software Cofig. Current Range:	0.5 - 7.0 A (default by 6.0 A, increased by 0.1 A)
DIP Switch Functions:	Microstep, motor direction, auto-tuning, pulse mode, pulse edge
Logic Current Range:	7 - 16 mA (10mA typical)
Logic Voltage range:	5V or 24 VDC
Communication Type:	RS232 for tuning
Pulse enabled at:	Falling edge
Software Config. Idle Current Percentage:	0 - 100%
# of Digital Inputs:	3
Digital Outputs:	2 Outputs can be configured to Fault output, brake control or in-position output
Step Width:	2.5 us (when dutycycle = 50% )
Minimal Direction Setup Time:	5 us
Protection:	Over current; over voltage; chip error; motor cable error; ROM error; auto-tuning error; position following error;
Isolation Resistance:	500 Mohm
Environment:	Avoid dust, oil fog and corrosive gases
Operating Temperature:	0 - 50 °C
Humidity:	40 - 95% RH
Vibration:	5.9 m/s2 Max
Storage Temperature:	-20 - 65°C
Mechanical:	116 * 69.2 * 26.5 mm
Weight:	280g

(CS-D507E) Closed Loop Stepper Drive

Downloads

CS-D507E_User_Manual

Leadshine-Motion-Studio-Stepper-V1.3.10

Certification

Menu

Contact us